Accessing an external hard drive, SD card, or USB flash drive in Windows 11 can be blocked by a critical filesystem error: Location is not available. E:\ is not accessible. The drive cannot find the sector requested. In other cases, this error surfaces during Windows Backup or system image creation with error code 0x8007001B. This alert indicates that the operating system storage driver issued a read/write command to a specific physical sector on the magnetic platter or NAND flash, but the hardware controller returned an unreadable sector response.
Recovering access requires running low-level volume repairs with CHKDSK, repairing corrupted partition tables, updating storage controller drivers, and verifying drive hardware health via S.M.A.R.T. telemetry.
What Causes ‘The Drive Cannot Find the Sector Requested’?
Every storage device is formatted into sectors (typically 512 bytes or 4096 bytes / Advanced Format). The error occurs due to:
- Physical Bad Sectors: Magnetic platter degradation or worn NAND flash blocks that can no longer maintain electrical charge or magnetic polarity.
- Filesystem Catalogue Corruption: The Master File Table (MFT) or File Allocation Table (FAT) contains invalid sector offsets pointing to non-existent disk coordinates.
- Unsafe Device Removal: Unplugging an external drive while write caching was active leaves unfinished sector writes.
- Insufficient USB Bus Voltage: Unpowered USB hubs or loose cables causing temporary controller brownouts during read operations.
- Outdated Storage Controller Drivers: AHCI or USB mass storage drivers misinterpreting LBA (Logical Block Addressing) boundaries on large drives (2 TB+).
Step 1: Check Physical Cables and Switch USB Ports
Electrical drops frequently mimic hardware bad sectors by interrupting data packets mid-transfer:
- Disconnect the external hard drive or flash drive from any intermediate USB hubs or keyboard passthrough ports.
- Connect the drive directly to a rear motherboard USB 3.0/3.1 port on a desktop PC, or directly into the side chassis of a laptop.
- If the drive is a 3.5-inch external enclosure, ensure its dedicated AC power adapter is securely connected to a wall socket.
- Replace the USB-A or USB-C data cable to rule out worn internal wire shielding.
Step 2: Run CHKDSK to Scan and Remap Bad Sectors
The Windows Check Disk utility scans the physical storage surface and reallocates readable data away from damaged sectors:
- Press
Windows Key + Xand select Terminal (Admin) or Command Prompt (Admin). - Identify your drive letter in File Explorer (for example, drive
E:). - Execute the following repair command:
(Parameters explained:chkdsk E: /f /r /x/ffixes structural errors;/rlocates bad sectors and recovers readable information;/xforces the volume to dismount first.) - Allow the scan to process through all five stages. This process can take from 20 minutes to several hours depending on drive capacity.
- Once complete, review the log to confirm whether bad sectors were found and reallocated to spare sectors.
Step 3: Reinstall Storage Controller and USB Drivers
Corrupted driver stacks cause communication timeouts between Windows and the drive interface:
- Press
Windows Key + Xand choose Device Manager. - Expand the Disk drives category.
- Right-click your problematic external drive and choose Uninstall device. Confirm with Uninstall.
- Next, expand Universal Serial Bus controllers.
- Right-click USB Mass Storage Device (or USB Root Hub) and select Uninstall device.
- Disconnect the drive, restart your PC, and reconnect the drive to let Windows install fresh driver packages.
Step 4: Inspect S.M.A.R.T. Health Status via PowerShell
Determine whether the drive is experiencing imminent hardware failure before attempting further writes:
- Open PowerShell as Administrator.
- Execute:
wmic diskdrive get status,model,name - If the status reports Pred Fail (Predictive Failure) instead of OK, the drive controller has exhausted its spare reallocated sectors. Immediately copy critical data off the drive before it fails permanently.
- For granular health metrics, run a third-party diagnostic tool such as CrystalDiskInfo to check the Reallocated Sectors Count and Current Pending Sector Count.
Step 5: Format the Drive (If Hardware Is Healthy but Filesystem Is RAW)
If CHKDSK reports that the filesystem is RAW and data is already backed up:
- Press
Windows Key + R, typediskmgmt.msc, and press Enter to open Disk Management. - Locate the problematic drive volume in the bottom pane.
- Right-click the volume and select Format….
- Choose NTFS (for Windows-only use) or exFAT (for cross-platform use), set Allocation unit size to Default, and ensure Perform a quick format is unticked to perform a full zero-pass scan.
- Click OK to format the partition and rebuild the sector map.