In modern enterprise IT environments, distributed data centers, and remote computer laboratories, systems administrators require reliable mechanisms to power on workstations remotely. Standard Wake-on-LAN (WoL) allows machines to awaken from ACPI low-power sleep states (S3) or Modern Standby (S0 Low Power Idle). However, when a Windows 11 computer is completely shut down (ACPI power state S5) or placed into hibernation (S4), default operating system power profiles sever power to network interface transceivers to comply with international energy standards such as Energy Star and EU ErP Lot 6. To enable remote power-on of fully powered-off desktop workstations, administrators must explicitly configure Wake on Magic Packet from power off state on the physical Ethernet controller. In Windows 11, configuring this setting via PowerShell ensures reliable out-of-band power management without manual BIOS/UEFI intervention.
Understanding Wake on Magic Packet from S5 (Cold Shutdown)
In ACPI power management architecture, operating systems navigate distinct system power states:
- ACPI S3 (Sleep): System RAM remains refreshed while the CPU, storage, and PCIe peripherals power down. The network adapter retains power to listen for wake signals.
- ACPI S4 (Hibernate): System state is written to disk (
hiberfil.sys), and the main power domains are disconnected. - ACPI S5 (Soft Off / Cold Shutdown): The operating system has fully halted, and all main power rail voltages are dropped. Only the auxiliary power rail (Vaux) remains active on the motherboard.
When Wake on Magic Packet from power off state is enabled, the Ethernet controller’s integrated firmware and PHY layer continue running on auxiliary power even when Windows 11 has completed a full shutdown. When an authorized Magic Packet arrives over the physical network cable, the network controller asserts the PME (Power Management Event) pin on the PCIe bus, signalling the motherboard’s power delivery unit to cold boot the computer into Windows.
Inspecting Physical Network Adapters in PowerShell
To inspect your wired Ethernet hardware and identify advanced property names, launch Windows PowerShell as an Administrator.
Query all physical network adapters active on the operating system:
Get-NetAdapter -Physical | Where-Object { $_.MediaType -eq "802.3" } | Select-Object Name, InterfaceDescription, LinkSpeed, Status
Note the interface name representing your primary wired adapter (typically designated as Ethernet).
Querying Current Wake from Power Off State Configurations
Because hardware vendors (such as Intel, Realtek, and Broadcom) use standardized NDIS registry keywords alongside proprietary display labels, query the advanced properties of the Ethernet adapter:
Get-NetAdapterAdvancedProperty -Name "Ethernet" | Where-Object { $_.DisplayName -match "Power Off|S5|Magic Packet from" -or $_.RegistryKeyword -match "WakeOnMagicPacketFromS5" }
On modern enterprise Ethernet adapters (such as the Intel I219-LM, I225-V, or Realtek PCIe 2.5GbE), PowerShell returns the property status:
Name DisplayName DisplayValue ValidDisplayValues
---- ----------- ------------ ------------------
Ethernet Wake on Magic Packet from power off state Disabled {Enabled, Disabled}
If DisplayValue reports Disabled, the network adapter shuts down its receiver during a system power-off, ignoring incoming Magic Packets when the computer is shut down.
Enabling Wake on Magic Packet from Power Off State
To enable the network adapter to listen for remote Magic Packets while completely powered off, use the Set-NetAdapterAdvancedProperty cmdlet:
Set-NetAdapterAdvancedProperty -Name "Ethernet" -DisplayName "Wake on Magic Packet from power off state" -DisplayValue "Enabled"
To guarantee uniform execution across multi-language enterprise operating systems where property display names are localized, target the standardized NDIS registry keyword directly:
Set-NetAdapterAdvancedProperty -Name "Ethernet" -RegistryKeyword "*WakeOnMagicPacketFromS5" -RegistryValue "1"
The network adapter driver will reload its configuration table, momentarily resetting the physical Ethernet link for one to two seconds.
Disabling the Feature for Energy Conservation Compliance
If the workstation must adhere strictly to strict EU Lot 6 energy efficiency regulations requiring sub-0.5 watt standby power draw during shutdown, disable the feature:
Set-NetAdapterAdvancedProperty -Name "Ethernet" -DisplayName "Wake on Magic Packet from power off state" -DisplayValue "Disabled"
Or using the registry keyword parameter:
Set-NetAdapterAdvancedProperty -Name "Ethernet" -RegistryKeyword "*WakeOnMagicPacketFromS5" -RegistryValue "0"
Confirm the modification by re-querying the registry keyword value:
(Get-NetAdapterAdvancedProperty -Name "Ethernet" -RegistryKeyword "*WakeOnMagicPacketFromS5").DisplayValue
Configuring Mandatory Fast Startup and Power Management Settings
In Windows 11, the default “Fast Startup” feature places the kernel into a hybrid hibernation state rather than a pure ACPI S5 shutdown. In certain motherboard firmware implementations, hybrid shutdown can interfere with auxiliary PCIe power delivery.
To ensure consistent remote power-on behaviour from cold shutdown, ensure the standard power management wake settings are enabled:
Set-NetAdapterPowerManagement -Name "Ethernet" -WakeOnMagicPacket Enabled -AllowComputerToTurnOffDevice Enabled
If wake-from-power-off continues to fail after shutting down Windows, disable Fast Startup via the registry to ensure Windows executes a clean ACPI S5 shutdown:
Set-ItemProperty -Path "HKLM:\SYSTEM\CurrentControlSet\Control\Session Manager\Power" -Name "HiberbootEnabled" -Value 0
Testing Remote Power-On Across Subnets
To verify the configuration, shut down the target Windows 11 computer completely using PowerShell:
Stop-Computer -Force
Observe the physical Ethernet port on the rear of the computer chassis: the physical link LED (typically amber or green) should remain illuminated, confirming that the transceiver is operating on auxiliary motherboard power. From another machine on the network, transmit a directed Magic Packet to the target’s MAC address to verify that the workstation powers on reliably.