How to Fix ‘The iPad Could Not Be Restored. An Unknown Error Occurred (4013)’

Connecting your iPad to a computer to update or restore iPadOS only to encounter the error: ‘The iPad could not be restored. An unknown error occurred (4013)’ halts device recovery immediately. This error commonly appears while the iPad displays a progress bar stuck at 1% or remains frozen on the Apple logo. In Apple diagnostic terminology, Error 4013 is primarily a communication disconnect exception. It indicates that the connection between the computer and the iPad was severed or interrupted at the exact moment the bootloader attempted to write low-level firmware NAND blocks.

Root Causes of iPad Restore Error 4013

Error 4013 is notoriously sensitive to hardware transmission stability. Common failure triggers include:

  • Faulty or Third-Party Lightning / USB-C Cables: Aftermarket cables that support battery charging but lack high-speed, shielded data throughput lines causing packet dropouts during firmware verification.
  • Intermediary USB Hubs and Adapters: Connecting via unpowered USB splitters, monitor passthrough ports, or keyboard hubs that throttle bus voltage under sustained transfer loads.
  • Outdated iTunes or Apple Devices Software: Desktop software lacking updated mobile device drivers required to communicate with recovery-mode bootloaders.
  • Internal Hardware Sensor Faults: In rare cases, physical liquid ingress into the ambient light sensor or TrueDepth camera assembly causing a logic board voltage short during the restore handshake.

Step 1: Replace the Cable and Connect Directly to Motherboard Ports

Eliminating cable noise and intermediary hubs resolves over 70% of Error 4013 occurrences.

  1. Disconnect the iPad from any USB hubs, docking stations, or front-panel computer ports.
  2. Use an official Apple genuine USB cable or an MFi-certified high-speed data cable.
  3. Plug the cable directly into a rear motherboard USB port on a desktop PC, or directly into a Thunderbolt/USB-C port on a Mac.
  4. Inspect the iPad’s charging port with a flashlight. Use an anti-static toothpick to gently remove compacted pocket lint or debris preventing full pin contact.

Step 2: Update Computer Software and Operating System

The host computer requires the latest Apple Mobile Device USB drivers to handle firmware staging.

  1. On a Mac: Click the Apple menu > System Settings > General > Software Update. Ensure macOS and Finder device support components are fully updated.
  2. On Windows 11: Open the Microsoft Store app, check for updates to the Apple Devices app (or update iTunes to the latest version).
  3. Restart your computer after applying software updates to refresh USB driver services.

Step 3: Force Device Firmware Update (DFU) Mode

If standard Recovery Mode fails with Error 4013, putting the iPad into Device Firmware Update (DFU) mode bypasses the corrupted operating system and bootloader entirely.

  1. Connect your iPad directly to your computer.
  2. For iPads without a Home Button:
    • Press and quickly release Volume Up.
    • Press and quickly release Volume Down.
    • Press and hold the Top (Power) button for 10 seconds until the screen goes black.
    • While still holding the Top button, press and hold the Volume Down button for 5 seconds.
    • Release the Top button but continue holding Volume Down for another 10 seconds.
    • The screen must remain completely black. If the Apple logo appears, you held buttons too long and must retry.
  3. For iPads with a Home Button: Hold both the Home button and Top (Power) button simultaneously for 8 seconds, then release Power while continuing to hold Home for 10 seconds.
  4. Your computer will detect an iPad in recovery mode. Click Restore to install a fresh image of iPadOS.

Step 4: Test on an Alternative Computer

Third-party security suites, corrupted Windows USB controller drivers, or background software conflicts on the host computer can terminate firmware handshakes.

  1. Temporarily disable third-party antivirus, firewalls, and VPN software on your computer.
  2. If Error 4013 persists, attempt the restore process on an entirely different Mac or Windows computer.
  3. If the iPad fails across multiple computers and verified cables, physical logic board or NAND flash damage requires service from an Apple Authorised Service Provider.

Get the best tech tips delivered straight to your inbox.

Join thousands of readers mastering Apple, Google, Microsoft, and Linux.