How to Fix iPhone Screen Flickering or Glitching

Interacting with an iPhone—whether scrolling through social feeds, browsing webpages, or watching streaming video—relies on a responsive, rock-solid OLED or LCD display. However, users occasionally experience an alarming visual disruption where the iPhone screen rapidly flickers, flashes white or green, stutters during brightness changes, or displays horizontal scan lines. While a flickering screen can suggest physical drop or water damage, subtle software rendering glitches, aggressive ambient light sensors, and conflicting accessibility filters are frequently the true cause.

What Causes an iPhone Screen to Flicker or Glitch?

Apple Super Retina XDR OLED panels modulate light using high-frequency Pulse-Width Modulation (PWM) and dynamic ProMotion refresh rates (10Hz to 120Hz). Screen flickering typically arises from:

  • Pulse-Width Modulation (PWM) Stutter at Low Brightness: At extremely low brightness levels, rapid LED cycling can appear as visible strobing or flickering to the human eye.
  • Conflicting Ambient Light and True Tone Sensors: A smudged or partially obscured ambient light sensor located in the Dynamic Island / notch rapidly cycling backlight voltage up and down.
  • Accessibility ‘Reduce White Point’ Conflicts: Having Reduce White Point enabled alongside Auto-Brightness causing display gamma calculation loops.
  • GPU Compositor Memory Leaks in iOS: Temporary graphical memory buffer corruption inside the iOS Springboard rendering engine.
  • Loose Display Flex Cable or Liquid Ingress: Physical hardware separation between the display panel connector and the iPhone logic board following a drop.

Step 1: Perform a Hard Force Restart to Reset Display Buffers

A force restart clears the active graphical framebuffer and resets the iOS display compositor hardware controller without wiping your stored data.

  1. For iPhone 8, iPhone SE (2nd/3rd gen), iPhone X, 11, 12, 13, 14, 15, and 16 models:
    • Press and quickly release the Volume Up button.
    • Press and quickly release the Volume Down button.
    • Press and hold the Side Power button continuously.
    • Do not release the button when ‘slide to power off’ appears; continue holding until the screen goes black and the silver Apple logo appears.
    • Release the button and let iOS boot cleanly.
  2. Inspect the display during boot. If the Apple logo displays solidly without any flickering, the display hardware is intact and the flicker was caused by software memory leaks.

Step 2: Disable Auto-Brightness and True Tone

A fluctuating ambient sensor can cause the backlight controller to pulse rapidly.

  1. Open Settings on your iPhone.
  2. Tap Display & Brightness.
  3. Toggle True Tone to Off.
  4. Next, navigate to Settings > Accessibility > Display & Text Size.
  5. Scroll down to the very bottom of the page and toggle Auto-Brightness to Off.
  6. Manually adjust the brightness slider in Control Centre to approximately 50%. Observe whether screen flickering ceases immediately.

Step 3: Check and Disable ‘Reduce White Point’

Reduce White Point suppresses bright colours electronically, which can trigger PWM strobing on OLED panels.

  1. Navigate to Settings > Accessibility > Display & Text Size.
  2. Scroll down to find Reduce White Point.
  3. If this option is toggled On, turn it Off.
  4. When active, high reduction percentages (such as 80% to 100%) force OLED diodes to operate at unstable minimum voltages that induce visible flickering.

Step 4: Lock Refresh Rate to 60Hz (On ProMotion Models)

On iPhone Pro models equipped with 120Hz ProMotion displays (iPhone 13 Pro and newer), variable refresh rate switching can stutter during rapid frame rate drops.

  1. Open Settings > Accessibility.
  2. Tap Motion.
  3. Locate the setting labelled Limit Frame Rate.
  4. Toggle Limit Frame Rate to On. This caps the display at 60 frames per second, eliminating refresh rate shifting glitches.
  5. If the flicker disappears, an iOS update will typically resolve the underlying ProMotion driver timing bug.

Step 5: Clean the Ambient Sensor Cluster

Dust, lint, or low-quality screen protectors over the top speaker notch confuse ambient light sensors.

  1. Examine the top edge of your iPhone screen around the Dynamic Island or notch.
  2. Clean the glass thoroughly using a dry microfiber cloth to remove skin grease and dust.
  3. If using a thick, privacy-tinted glass screen protector with misaligned sensor cut-outs, temporarily remove the protector to verify whether sensor occlusion was triggering backlight cycling.

Get the best tech tips delivered straight to your inbox.

Join thousands of readers mastering Apple, Google, Microsoft, and Linux.